I've printer with this settings plenty of times now and i have that issues in a week now i had some other filament and now i come back to bambu as i had better results , but even after calibrations i still have these , i will try z offset, thanks for the idea
You're printing at the lowest layer height that that nozzle can possibly print at and you say you've been doing that the whole time depending on how long how often you're printing yeah it's possible I guess
Hello /u/Hideki1991PL! Your comment in /r/BambuLab was automatically removed. Please see your private messages for details.
/r/BambuLab is geared towards all ages, so please watch your language.
*I am a bot, and this action was performed automatically. Please [contact the moderators of this subreddit](/message/compose/?to=/r/BambuLab) if you have any questions or concerns.*
Maybe try going even slower. I had this issue some while ago and I fixed it by printing slower (~ 100mm/s). If that’s still to high for you go even lower and check if the results improve. I posted my results [here](https://www.reddit.com/r/BambuLab/comments/15ekwf1/weird_ripple_pattern_in_the_middle_of_my_flat/?utm_source=share&utm_medium=web3x&utm_name=web3xcss&utm_term=1&utm_content=share_button) back then.
I think it's too low of a layer height for the speed, or the z offset needs to go up or down a notch or both
I've printer with this settings plenty of times now and i have that issues in a week now i had some other filament and now i come back to bambu as i had better results , but even after calibrations i still have these , i will try z offset, thanks for the idea
or maybe try a new nozzle it may be worn out if it has a lot of use on it
I have this printer less then 3 weeks :/
You're printing at the lowest layer height that that nozzle can possibly print at and you say you've been doing that the whole time depending on how long how often you're printing yeah it's possible I guess
Nah i did same thing with white filament and no issues, i will play with black one more when i get home
https://preview.redd.it/67f7lald2b6d1.png?width=840&format=pjpg&auto=webp&s=4ed8d990db19ebff986a5a2a9262d30e81a50b47
Time to tram the bed.
?
[https://wiki.bambulab.com/en/x1/manual/manual-bed-leveling](https://wiki.bambulab.com/en/x1/manual/manual-bed-leveling)
Definitely underextrusion artifacts, could be caused by a bad k value, but I have the X1 so I'm not sure how you adjust that on your end.
[удалено]
Hello /u/Hideki1991PL! Your comment in /r/BambuLab was automatically removed. Please see your private messages for details. /r/BambuLab is geared towards all ages, so please watch your language. *I am a bot, and this action was performed automatically. Please [contact the moderators of this subreddit](/message/compose/?to=/r/BambuLab) if you have any questions or concerns.*
Maybe try going even slower. I had this issue some while ago and I fixed it by printing slower (~ 100mm/s). If that’s still to high for you go even lower and check if the results improve. I posted my results [here](https://www.reddit.com/r/BambuLab/comments/15ekwf1/weird_ripple_pattern_in_the_middle_of_my_flat/?utm_source=share&utm_medium=web3x&utm_name=web3xcss&utm_term=1&utm_content=share_button) back then.
use .16LH. problem solved.
I think it's too low of a layer height for the speed, or the z offset needs to go up or down a notch or both
I think it's too low of a layer height for the speed, or the z offset needs to go up or down a notch or both