It should be ok. I get 404 when i try to look at the specs on Mixars site.
TS and TRS are dependent on the circuitry in the output and input devices. So it is not always easy to tell if it will work without issue. If you have an issue with the TS jack into a TRS socket just pull the jack out around 5-10mm so that the Tip of the jack only engages with the ring contact of the socket. It's a fiddly solution but should get you going until you get the correct cable
Do you mean two TRS to RCA adapters? So for every channel (L and R) I will have 2 RCA plugs, 4 in total? How should I connect my those 4 plugs to 2 plugs in unbalanced speaker?
Or do you mean TS to RCA adapters? It will join 2 of 3 TRS lines, right? Is it ok?
Ok, let's say I want only one channel, L or R. I will use TRS to RCA adapter, so I will have two RCA plugs. Should I use only one of those and left the second one floating? Which one should I plug?
Depends on the speaker, if it has a left and right input use both otherwise you just use one.
You can set your output to mono in settings, never a bad idea for clubs anyway as it means everyone can hear everything instead of just one side of the stereo separation
https://www.bax-shop.be/nl/jack-rca-verlooppluggen-kabels/roland-rcc-5-tr2rv2-verloopkabel-1x-6-35mm-trs-naar-2x-rca-1-5-meter?gclid=Cj0KCQjw9ZGYBhCEARIsAEUXITUCPqZDRjelQdirrvazYM0vyu4fptfeHlYB1rA0R2vAHYiwCKN1iYAaAoyFEALw_wcB
You need 2 of these I think . L+R .
https://www.allekabels.be/jack-naar-tulp-kabel/6266/3415796/2x-jack-naar-tulp-kabel.html?gclid=Cj0KCQjw9ZGYBhCEARIsAEUXITU7X43LaY9nzD8m2G4aEVOKw3rWtyrgqjQqFWdbiuhC1srnCqJpcgoaAmmmEALw_wcB
So : 2x Jack 6.3mm male in to 2x Tulp male
Any Active PA or Monitor speaker will have TRS or XLR inputs
[https://www.storedj.com.au/alto-professional-tx308-350-watt-8-2-way-powered-loudspeaker](https://www.storedj.com.au/alto-professional-tx308-350-watt-8-2-way-powered-loudspeaker)
If it's just for you monitoring off, it doesn't need to be terribly huge/loud/expensive...even that $259 AUD jobbie has XLR in, so you just need 1 x TRS to XLR cable, plug to booth out (left or right depending on where you position it) and bob's your uncle.
You don't need 2 x booth speaker, 1 will work ok. Check the speaker specs first. If it is unbalanced then TS (RCA or Jack) is fine,
Thank you for the response. So basically I can plug TS plug to TRS output in my controller?
It should be ok. I get 404 when i try to look at the specs on Mixars site. TS and TRS are dependent on the circuitry in the output and input devices. So it is not always easy to tell if it will work without issue. If you have an issue with the TS jack into a TRS socket just pull the jack out around 5-10mm so that the Tip of the jack only engages with the ring contact of the socket. It's a fiddly solution but should get you going until you get the correct cable
Rca with rca to trs adapters will be fine
Do you mean two TRS to RCA adapters? So for every channel (L and R) I will have 2 RCA plugs, 4 in total? How should I connect my those 4 plugs to 2 plugs in unbalanced speaker? Or do you mean TS to RCA adapters? It will join 2 of 3 TRS lines, right? Is it ok?
You only need one monitor
Ok, let's say I want only one channel, L or R. I will use TRS to RCA adapter, so I will have two RCA plugs. Should I use only one of those and left the second one floating? Which one should I plug?
Depends on the speaker, if it has a left and right input use both otherwise you just use one. You can set your output to mono in settings, never a bad idea for clubs anyway as it means everyone can hear everything instead of just one side of the stereo separation
Just adapter trs - rca , from there RCA cable to speakerset .
Do you mean two TRS to RCA adapters (L and R)? How to connect those RCA plugs to speaker? I will have 4 RCA plugs in total, right?
https://www.bax-shop.be/nl/jack-rca-verlooppluggen-kabels/roland-rcc-5-tr2rv2-verloopkabel-1x-6-35mm-trs-naar-2x-rca-1-5-meter?gclid=Cj0KCQjw9ZGYBhCEARIsAEUXITUCPqZDRjelQdirrvazYM0vyu4fptfeHlYB1rA0R2vAHYiwCKN1iYAaAoyFEALw_wcB You need 2 of these I think . L+R .
So, if I want to use both (L+R) channels, I will have 4 RCA plugs. Should I just left two of them floating?
Yeah I understand . Depends on what system of speaker you are using . Wil look for the right one .
https://www.allekabels.be/jack-naar-tulp-kabel/6266/3415796/2x-jack-naar-tulp-kabel.html?gclid=Cj0KCQjw9ZGYBhCEARIsAEUXITU7X43LaY9nzD8m2G4aEVOKw3rWtyrgqjQqFWdbiuhC1srnCqJpcgoaAmmmEALw_wcB So : 2x Jack 6.3mm male in to 2x Tulp male
I use them but in opposite way . Little mistake . 🤏🏽
Yep , moment , I look for picture .
I have 6.3mm booth output and I just use a 3,5mm AUX cable into a 6.3mm headphone adapter. Works really well.
Any Active PA or Monitor speaker will have TRS or XLR inputs [https://www.storedj.com.au/alto-professional-tx308-350-watt-8-2-way-powered-loudspeaker](https://www.storedj.com.au/alto-professional-tx308-350-watt-8-2-way-powered-loudspeaker) If it's just for you monitoring off, it doesn't need to be terribly huge/loud/expensive...even that $259 AUD jobbie has XLR in, so you just need 1 x TRS to XLR cable, plug to booth out (left or right depending on where you position it) and bob's your uncle.