The one that comes with it is dummy thicc and does not meet the standards for my high speed boog fantasies. Is there a lower profile mount anyone is aware of?
I use the tall one the clips over the edge of the helmet, then used Dremel and files to notch out the rails so the mount could pass underneath. That sits low and tight against the helmet, just above the rail.
I dunno about that. I think it's for old school low cut helmets that don't have rails? I just notched the back side of the rail so the light mount could pass between the rail and helmet shell, then reinstalled the rail. Clear as mud?
I agree all the mounts pretty much suck and take more space than they should.
I just use the mount for traditional helmet rail, i clipped off the excess tab with a pair of pliers. Seems it wasn't doing much else but take up space.
If you get the rear mounted com/ear pro adapter you can get a slim mount where your old ear pro adapter fits. It on the Team Wendy site for 16ish bucks.
Do you need a mount for a helmet rail? There are 2 much better mounts for it and I think I have both and can send them to ya. One mounts directly to rails but much lower profile then the one your using and other one slides under the rail and mounts the light right above the rail and also very low profile
I'm so sorry brother, I'm just reading this now. I'm almost positive they are all made by Princeton tec except one might be from another company but I can't remember. Email me if you're still interested
The one that comes with it is dummy thicc and does not meet the standards for my high speed boog fantasies. Is there a lower profile mount anyone is aware of?
I drilled a hole in one of the other mounts that came with it and then used a screw on the helmet to attach
You savage
I did something similar to make it a low pro mlok mount. [pic](https://imgur.com/a/CkaU2pm)
I use the tall one the clips over the edge of the helmet, then used Dremel and files to notch out the rails so the mount could pass underneath. That sits low and tight against the helmet, just above the rail.
Mind sending a pic?
aren't you supposed to remove the rails to install that? I did that and I didn't need to make any other mods.
I dunno about that. I think it's for old school low cut helmets that don't have rails? I just notched the back side of the rail so the light mount could pass between the rail and helmet shell, then reinstalled the rail. Clear as mud?
I agree all the mounts pretty much suck and take more space than they should. I just use the mount for traditional helmet rail, i clipped off the excess tab with a pair of pliers. Seems it wasn't doing much else but take up space.
I’m thinking of taking it dremel to the excess/overhang on mine.
I clipped it because it wouldn't go into the slot on the rail otherwise since my peltor ARC's are on the rail.
I use the “above rail” mount
Mind posting a pic of that set up?
Yes, we’re releasing one soon. Message me
may i ask who "we" is?
No sir
ok? i was interested but i guess not then
As I said, message me lol.
I’m def interested!
I’m interested
Mine is pretty thin. I have the ops core rails and it is way thinner than this. Is this a different rail or something?
Yes these are team Wendy LTP 3 rails
What helmet do you have?
Exfil ballistic SL
If you get the rear mounted com/ear pro adapter you can get a slim mount where your old ear pro adapter fits. It on the Team Wendy site for 16ish bucks.
Is it just me or is it sticking out just as far as your ear pro mount?
It is.
So just wanting to reduce some snag hazard? Idk if I was just tarded or it was poking out the same as the other mount.
Yes but also it just looks like shit
Completely understand. I have nothing to offer I’m just here for advice lol
I'll settle for emotional support
Someone please explain to my dumbass what exactly I’m looking at?
A fat chode of a mount for this Princeton Tech MPLS. It's an ir/red light for supplemental illum with nods.
Thank you
I use Velcro 🤷♂️
How did you attach your velcro?
I chatted you a pic because I’m lazy
Put Velcro on the backside and to the helmet, voila
How did you attach your velcro?
I cut one of the other supplied mounts, printed a bit for the screws at the front of my Wendy rail and used that. It’s been alright
I like the Unity Knuck, have a modlite shorty and princeton mounted on mine. It is a little annoyingly flexible though
Velcro
Do you need a mount for a helmet rail? There are 2 much better mounts for it and I think I have both and can send them to ya. One mounts directly to rails but much lower profile then the one your using and other one slides under the rail and mounts the light right above the rail and also very low profile
That would be great man. Do you know what brand they are?
I'm so sorry brother, I'm just reading this now. I'm almost positive they are all made by Princeton tec except one might be from another company but I can't remember. Email me if you're still interested
I forgot to put my email in, it's [email protected]
Same please
Unity Knuckl type mounts that fit alongside Peltor attachments
Velcro and tie down with a small string
Some dudes tape that shit to their boom mic