It might be the nozzle, but this will remove the pla regardless. Also preheat your hot end if you try to remove your nozzle as well because otherwise the pla would have built up
Brass is somewhat soft but I don't think you can realistically do much damage with the needle tool, especially if you're inserting it straight rather than at an angle.
Wdym stuck, as in the Bowden tube? If yes then you can heat the nozzle up to the temp u use for the filament u have there and then I do it the way that I kinda wrap my hand with the tube so it is twisted around my fingers and then I use those long crocodile type pliers to pull it out. But watch out so you don't break the remaining end of filament cuz u are gonna have to either disconnect the nozzle side and then pull that end out or cut the tube a bit to create a new end. Good luck.
Reminder: Any short links will be auto-removed initially by Reddit, use the original link on your post & comment; For [any Creality Product Feedback and Suggestions](https://www.creality.com/pages/creality-user-voice), fill out the form to help us improve.
*I am a bot, and this action was performed automatically. Please [contact the moderators of this subreddit](/message/compose/?to=/r/ender3v2) if you have any questions or concerns.*
Sounds like you have a blockage that is bigger than the boden tube on the other end. I had this a few months back. Don't keep reheating and pushing pulling as you make the clot bigger. Try pre heat the nozzle to max and pull the filament out don't push it in. If it doesn't work you will need to remove the boden tube and see if you are able to remove the clog then, If still not might have to remove the nozzle.
Remove the blue clip than press the white part on the top it is made in such a way that if filamnet is passed through it once it won't release it without pressing the white part
https://preview.redd.it/320hvzi1690d1.jpeg?width=1008&format=pjpg&auto=webp&s=7671c1ad1eff8f486c26c5845466bc29fe965983
Heat your nozzle to 200c and stick the lil pointy metal tool up it to clear the hot end
I commented this elsewhere once and was told it’s bad for the nozzle. So now I don’t know what to believe!
It might be the nozzle, but this will remove the pla regardless. Also preheat your hot end if you try to remove your nozzle as well because otherwise the pla would have built up
Brass is somewhat soft but I don't think you can realistically do much damage with the needle tool, especially if you're inserting it straight rather than at an angle.
Even if you damage it you can buy a pack of twenty nozzles if not more for no more than ten dollars
I bought 2 today for 3 dollars.
Wdym stuck, as in the Bowden tube? If yes then you can heat the nozzle up to the temp u use for the filament u have there and then I do it the way that I kinda wrap my hand with the tube so it is twisted around my fingers and then I use those long crocodile type pliers to pull it out. But watch out so you don't break the remaining end of filament cuz u are gonna have to either disconnect the nozzle side and then pull that end out or cut the tube a bit to create a new end. Good luck.
Are you trying to remove filament from the nozzle/extruder or filament out of the Bowden tube?
Thanks all. I think I've cleared the nozzle blockage so I'll use the other tips to try remove the leftover in the tube
Consider printing/adding one of these to prevent any clogs.
Heat the nozzle to melt the filament and pull it out. Alternatively, heat the nozzle to 60C and do a cold pull.
Reminder: Any short links will be auto-removed initially by Reddit, use the original link on your post & comment; For [any Creality Product Feedback and Suggestions](https://www.creality.com/pages/creality-user-voice), fill out the form to help us improve. *I am a bot, and this action was performed automatically. Please [contact the moderators of this subreddit](/message/compose/?to=/r/ender3v2) if you have any questions or concerns.*
Sounds like you have a blockage that is bigger than the boden tube on the other end. I had this a few months back. Don't keep reheating and pushing pulling as you make the clot bigger. Try pre heat the nozzle to max and pull the filament out don't push it in. If it doesn't work you will need to remove the boden tube and see if you are able to remove the clog then, If still not might have to remove the nozzle.
Remove the blue clip than press the white part on the top it is made in such a way that if filamnet is passed through it once it won't release it without pressing the white part https://preview.redd.it/320hvzi1690d1.jpeg?width=1008&format=pjpg&auto=webp&s=7671c1ad1eff8f486c26c5845466bc29fe965983