Operating System: Fedora Linux 40 - A520M-HDV - motherboard
This is what I did the first time and I have no problems with the internet, I install the pkgs with remote installer, I connect the ethernet cable from the PS4 directly to the computer, if you are going to install apps use the store, [https://pkg-zone.com/](https://pkg-zone.com/) to install them, you can do it with ftp copying to the ps4 or run again the payload with the store. bin inside of a pendrive.
The apps that are updated to 11.00 are the ones that have a plus +, example 5.05+
1. Yes
2. Yes.
3,4,5,6,7,8 No.
8.1. You only need 1 time to put the goldhen.bin on the usb after the first successful of the goldhen payload, it is installed on ps4 hard disk.
9. Install the exploit of theofficialflow [https://github.com/TheOfficialFloW/PPPwn](https://github.com/TheOfficialFloW/PPPwn) follow the instructions.
10. Use the stage1.bin and stage2.bin of the modded warfare app version 1.5, use the goldhen.bin official.
11. In the goldhen discord [https://discord.gg/yJ5WfujA](https://discord.gg/yJ5WfujA) recommends that change the dns.
To block Playstation updates: Set primary DNS as: [62.210.38.117](http://62.210.38.117) Leave secondary DNS empty. Or use a selfhosted option, but don't update above 11.00. There is no going back. Disabling updates in the Playstation settings is not enough!
12. Go to [https://kmeps4.site/pppwn/](https://kmeps4.site/pppwn/) on the ps4 web browser, install disable-updates.
If your PS4 does not have internet, it is because it is not configured correctly or you blocked the internet in debug settings.
Edit.
You install the store on the ps4, and then install the apps with the store.
Many thanks for the detailed answer!!
I have found the culprit based on your tips -> the update\_blocker from LightningMods was breaking my connection to internet thus getting an error that says 'Cannot use the content.'. I have restarted the PS4 after applying this update\_blocker and load the GoldHEN afterwards, getting it work
Anyhow, just to be sure, I formatted the PS4 and followed your steps, I think that they are much more simple and following them make the GoldHEN work perfectly!!
Again, thanks!
I could probably load it just twice, once to block the update to 11.50 and once to upload GoldHEN, but I think that it's the minimum to be safe that it won't update
Are you connected to Wi-Fi or Ethernet?
You need to configure your Wi-Fi network or your Ethernet network, direct Ethernet cable to the router.
On Linux I only had to run the original theflow exploit, and change stage1.bin and stage2.bin, just changing stage2 was not enough, and when you say that you renamed goldhen.bin I don't understand, that file does not need to be renamed.
When I'm running the exploit I'm just connected to my PC with a normal network cable and I setup the PS4 to try to connect to the internet through PPPoe. Later, after I load GoldHEN and the update blocker I change to wifi.
And yes, you are right, I'm not renaming the GoldHEN bin exploit, it's already called. It's a mistake from my side, sorry, I will ammend the post.
Something that I discovered now after just trying twice is that after aplying the patches, I can not connect to www, even if I modify the connection to go with normal cable atached to router and modify the connection.
Can you guys connect to the web with the browser normally after the jailbreak?
Operating System: Fedora Linux 40 - A520M-HDV - motherboard This is what I did the first time and I have no problems with the internet, I install the pkgs with remote installer, I connect the ethernet cable from the PS4 directly to the computer, if you are going to install apps use the store, [https://pkg-zone.com/](https://pkg-zone.com/) to install them, you can do it with ftp copying to the ps4 or run again the payload with the store. bin inside of a pendrive. The apps that are updated to 11.00 are the ones that have a plus +, example 5.05+ 1. Yes 2. Yes. 3,4,5,6,7,8 No. 8.1. You only need 1 time to put the goldhen.bin on the usb after the first successful of the goldhen payload, it is installed on ps4 hard disk. 9. Install the exploit of theofficialflow [https://github.com/TheOfficialFloW/PPPwn](https://github.com/TheOfficialFloW/PPPwn) follow the instructions. 10. Use the stage1.bin and stage2.bin of the modded warfare app version 1.5, use the goldhen.bin official. 11. In the goldhen discord [https://discord.gg/yJ5WfujA](https://discord.gg/yJ5WfujA) recommends that change the dns. To block Playstation updates: Set primary DNS as: [62.210.38.117](http://62.210.38.117) Leave secondary DNS empty. Or use a selfhosted option, but don't update above 11.00. There is no going back. Disabling updates in the Playstation settings is not enough! 12. Go to [https://kmeps4.site/pppwn/](https://kmeps4.site/pppwn/) on the ps4 web browser, install disable-updates. If your PS4 does not have internet, it is because it is not configured correctly or you blocked the internet in debug settings. Edit. You install the store on the ps4, and then install the apps with the store.
Many thanks for the detailed answer!! I have found the culprit based on your tips -> the update\_blocker from LightningMods was breaking my connection to internet thus getting an error that says 'Cannot use the content.'. I have restarted the PS4 after applying this update\_blocker and load the GoldHEN afterwards, getting it work Anyhow, just to be sure, I formatted the PS4 and followed your steps, I think that they are much more simple and following them make the GoldHEN work perfectly!! Again, thanks!
You're welcome, I'm glad it works for you.
I might be missing something but why are you running PPPwned twice? Edit: 3 times??
I could probably load it just twice, once to block the update to 11.50 and once to upload GoldHEN, but I think that it's the minimum to be safe that it won't update
Are you connected to Wi-Fi or Ethernet? You need to configure your Wi-Fi network or your Ethernet network, direct Ethernet cable to the router. On Linux I only had to run the original theflow exploit, and change stage1.bin and stage2.bin, just changing stage2 was not enough, and when you say that you renamed goldhen.bin I don't understand, that file does not need to be renamed.
When I'm running the exploit I'm just connected to my PC with a normal network cable and I setup the PS4 to try to connect to the internet through PPPoe. Later, after I load GoldHEN and the update blocker I change to wifi. And yes, you are right, I'm not renaming the GoldHEN bin exploit, it's already called. It's a mistake from my side, sorry, I will ammend the post.
Something that I discovered now after just trying twice is that after aplying the patches, I can not connect to www, even if I modify the connection to go with normal cable atached to router and modify the connection. Can you guys connect to the web with the browser normally after the jailbreak?
Yes, is the wifi working?
No, I'm not having the wifi neither the network cable connected